b'PUMPS APPLICATORS & SPRAYERSPOLYPROPYLENE HYDRAULIC MOTOR DRY MATERIALHANDLINGDRIVEN CENTRIFUGAL PUMPFMC-75-HYD-204FMC-75-HYD-206TRAILERS VALVES &FITTINGSTANKS &ACCESSORIESFMC-75-HYD-204 FMC-75-HYD-206-PWMSuction 1 Discharge 3/4PUMPS NOZZLES, TIPS & SPRAY GUNS-204 motor requires 4 GPM (15.1 LPM) hydraulic flow on PC Closed and Open Center Systems Oil FlowGPM4.84.33.6 2.8Conversion LPM 18.2 16.3 13.6 10.6-206 motor requires 7 GPM (26.75 LPM) hydraulic flow on LS Closed and Open Center Systems Maximum Shutoff Pressure 100 PSI-206-PWM motor with integrated PWM valve requires 7 GPM (26.5Note: Performance for pump with 204 motor.LPM) hydraulic flow on Closed Center Systems Do Not Run Dry - Seal damage will result from running dry. Impeller damage may Integral Needle Valve bypasses up to 9 GPM (34 LPM) on Open Centeralso occur if run dry for an extended period.Systems Do Not Run With Flow Shutoff For Extended PeriodsRunning the pump with no flow for extended periods of time will result in excessive Standard Viton Carbon/Ceramic or Optional Severe Duty Silicon Carbideheat and pump failure. A continuous bypass is recommended for low flow Mechanical Seal applications.Polypropylene Corrosion Resistant Construction Part # Part #STRAINERS & HOSEStainless Steel Shaft and Hardware FMC-75-HYD-204 FMC-75-HYD-206-PWMIdeal for planter set ups FMC-75-HYD-206 FMC-75SP-HYD-20475SP models include self-priming volute FMC-75SP-HYD-206FMC-75SP-HYD-206-PWMFLOW LIMITER VALVE PLANTEREQUIPMENTFOR USE ON LOAD SENSING OR PRESSURE-FLOW COMPENSATING CLOSED CENTER SYSTEMSSPRAYERCONTROLS &GUIDANCE11 12 134 10A5"L" "H" 6 7 8 9 10 10314 302 2927 28FMC-150F-HYD-206 INLET - "A" OUTLET - "B" 1 24 25 2621 22 2315 16 17 18 19 20NH3 PRODUCTSMODELS AND DIMENSIONSInstalls in Ace Hydraulic Motor Inlet Port 200 and 300 Series Motors (PRE 2005) 200N and 300N Series Motors (CURRENT)Shuts off all hydraulic flow when Hydraulic Motor Part # A B L H Part # A B L HEDP # EDP # the motors capacity is exceeded TECHNICAL INFORMATIONBAC-75-HYD-204 LS-204 3/8 NPT 3/8 NPT 3-1/4 7/8 LS-204N 1/2 NPT #8 SAE 3-1/4 1-1/8Protects Motor from overspeeding 41409 41417LS-206 LS-206NAutomatically Resets when BAC-75-HYD-206 41408 3/8 NPT 3/8 NPT 3-1/4 7/8 41418 1/2 NPT #8 SAE 3-1/4 1-1/8 hydraulic pressure is released BAC-75-HYD-210 LS-210 3/8 NPT 3/8 NPT 3-1/4 7/8 LS-210N 1/2 NPT #8 SAE 3-1/4 1-1/841411 41423Sizes available for all Ace models LS-304 LS-304N recommended for use on Load BAC-75-HYD-304 41413 1/2 NPT 1/2 NPT 3-5/16 1-1/8 41429 1/2 NPT 1/2 NPT 3-5/16 1-1/8 Sensing Hydraulic SystemsINDEX189'